What to do after wooden ceramic tile bubble water?

The phenomenon that wooden floor ceramic tile is soaked water is very common, a lot of friends are at a loss what to do after wooden ceramic tile is soaked water, do not know how to want to deal with wooden ceramic tile. The following is the introduction of LONGFAVOR ceramic tile to common treatment of wooden ceramic tile after soaking in water.

The treatment method of wooden ceramic tile bubble water

Plan 1: pry up wooden floor with "well" type fold put dry in the shade

Scope of application: floor that has been pried up after soaking in water

The solution: For a soaked floor, it's crucial to dry it out in a way that keeps the floor from deforming. After wiping the floor surface waters, according to the superposition of "well" word put, with its overlying weight to prevent the occurrence of deformation, should pay attention to when put to the floor on the opposite face, prevent surface caused by rapid drying dryness, at the same time pay attention to not in the sun exposure, should be placed in a ventilated place order, normally for good quality solid wood and engineered wood can be used again. Additional, should inform wooden ceramic tile floor after-sale service office in the first time when occurrence leak phenomenon, the oneself circumstance that staff member can combine a floor provides a solution to owner.

Plan 2: Take off kick a foot line

Applicable scope: Laminate floor soak water

Solution: no matter be large area bubble water or small area water, do not suggest floor of aggrandizement pry up air, cause damage easily to floor of floor of aggrandizement wooden ceramic tile in that way, cause the serious consequence that cannot use again very likely. Rapidly draining the floor surface water, and then remove the line that play a base of the floor, expansion joints, let finish expansion joints will send out water vapor, but according to different size into the water, dry up usually need to 7 to 15 days or so, the quality is better or immersion time is not long product can recover, if after 15 days still can't restore to replaced should be considered.

Plan 3: one side leaks water, two sides pry open ventilated

Range of application: with keel, small area of waterlogged wooden ceramic tile

Solution: the small area of water found in time, after the ground can be treated clean, pry up the board, dry the wet floor after re-installation; If into the water a little larger, not only to pry up the board in the water leakage, should also be along the direction of the keel set the opposite board also pry up, let the internal circulation air away moisture. If you can not determine the amount of water into the size, according to the direction of water in turn to pry up the board, check the moisture, make sure.

Plan 4: Use a high-powered vacuum cleaner

Scope of application: solid wood tile floor with direct paving and small area of water

Solution: If in a very short time in time to find the phenomenon of water, can be used to high-power vacuum water vapor suction. But when if large area takes in water, be about to lift floor board entirely pry up, undertake shade is dried according to the 2nd kind of plan. At the same time, if the indoor moisture is large, if the conditions can be installed in the indoor dehumidifier, the indoor moisture can be drained in a short time, but this operation scheme should have the floor drying identification technology.

Common quality problem of wooden ceramic tile

1. Distortion of wooden ceramic tile floor

Reason analysis: A. The wood material of the floor is not suitable; B. Improper processing technology and materials; C. The moisture content of the floor is controlled unevenly or the floor moisture content is not suitable for the environmental requirements of the place of use.

2. The gap between the wooden ceramic tile is too large

Cause analysis: A. The moisture content of the floor is too large; B. The indoor environment is too dry; C. The floor is poorly laid, resulting in floor movement.

3. Causes wooden ceramic tile floors to arch

Reason analysis: A. The reserved clearance between the floor and the wall foundation is not enough during the paving; B. There is no bridge treatment between rooms or insufficient gaps are reserved when bridge treatment is performed; C. The moisture content of the floor is too low when laying; D. The floor of the room is soaked by water because of water leakage; E. Wet ground or keel wood.

4. The difference between floors is too large

Cause analysis: A. Uneven ground; B. Uneven keel laying; C. Large deviation of floor thickness; D. The floor is deformed; E. Floor mortise processing does not match.

5. Wooden ceramic tile appears corrugated

Cause analysis: A. Uneven cement floor and excessive moisture content of keel during floor laying; B. Dry indoor environment; C. The moisture content of the floor is too high; D. Excessive indoor humidity and low floor moisture content.

6. Cracks appear in the wooden ceramic tile floor

Reason analysis: A. Wood performance is not suitable for making wooden floor; B. Moisture content of wooden ceramic tile is on the high side, indoor environment is dry and humidity is low.

7 Wood ceramic tile paint film peeling, crack, wrinkle

Cause analysis: A. The paint performance is not suitable for the floor material, resulting in the adhesion of the paint film and wood can not meet the use requirements, resulting in the phenomenon of peeling; B. The toughness of the paint film cannot meet the changes of natural wet swelling and drying shrinkage of the wood, resulting in cracks and wrinkles of the paint film; C. Peeling of the finish coat due to poor adhesion between the paint finish and the primer; D. Peeling, cracking and wrinkling of paint film caused by unscientific paint technology; E. The paint film is wrinkled and spalling due to the excessive moisture content of the floor; F. Paint film cracks or peeling due to too low moisture content of the floor; G. Due to the harsh indoor environment, such as too dry or wet indoor environment will also cause damage to the paint film.

8. The wooden ceramic tile changes color

Cause analysis: A. The discoloration of wood itself caused by external environment, such as sunlight and indoor air environment; B. Changes of paint caused by the influence of external environment; [C] changes caused by chemical reactions between paint and wood.

Notes for use of wooden ceramic tiles

1 wood ceramic tile floor laid, the ground, walls, wall foundation to ensure that dry.

2. The ground should be flat.

3 keel and the use of liner to dry, moisture content do not exceed the local equilibrium moisture content.

4. Keel level should be flat.

5. Lay the floor with a plastic film before laying the floor.

The moisture content of wooden ceramic tile should ensure inside standard limits, do not exceed local balance moisture content.

7 will tell to manufacturer, want scientific ground to choose a floor to use tree species, to the tree species that does not suit to make a floor, cannot use absolutely.

8. Because of the different tree species, the physical, chemical and mechanical properties of wood are different, so the factory should carry out tests when choosing paint. Confirm the adaptability of the paint to the material, scientific selection of paint, to ensure that the paint meets the performance of use.

9. When laying wooden ceramic tile floor, between the floor and wall foundation, the door and other places should reserve enough expansion joints according to the size of the room area.

10 in the floor laying process, try not to use water-soluble adhesive, to avoid due to the floor absorption of water caused by expansion, deformation.

11 keel must not be fixed with cement keel.

12. Indoor environment should not be too dry, also should not be too wet, especially in the winter of the north, indoor as far as possible to maintain a certain humidity, in case of wooden ceramic tile dry crack, deformation.

13. When cleaning wooden ceramic tiles, try not to clean them with a dripping mop.

14. Avoid floor exposure under strong sunlight to prevent floor discoloration, deformation and cracking.